Top 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Top 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Blog Article

Do not ignore the forklift at work. If the operation is not good, there will be major accidents in minutes, and there are lots of accidents involving forklifts.

Case 1: The forklift freight obstructed the driver's sight, and the person ahead can not be discovered, causing a moving crash.
Instance 2: In order to preserve the balance of the forklift when raising heavy goods, the staff members used their body weight as the counterweight, which almost triggered casualties.
Instance 3: The width of the forklift cargo surpasses the allowable size of the course and holds on the roadside rack, which nearly causes an mishap.
Case 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift motorist did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the workers illegally, the forklift driver does not use the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Situation 7: The forklift motorist did not use a safety belt and dropped from the vehicle when it rolled over and was crushed.
Forklift procedure should focus on these issues ：.

Start.
1. Before beginning, observe the environments, and after verifying that there are no barriers that impede the safety of driving, beep the horn initially and then start.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale have to be risk-free before beginning.
3. When the forklift starts with a lots, the vehicle driver ought to initially validate that the tons is stable and trustworthy.
4. The beginning has to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the pole must be tilted backward. .
2. Do not raise the fork expensive when driving. When getting in and leaving the job site or while driving, be careful that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork should be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly restricted to shut off the flame and slide, and it is forbidden to brake unexpectedly while driving with loads unless there are unique circumstances.
6. When the forklift is running, it must obey the web traffic rules in the factory and need to maintain a specific safety and security range from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not impede the driving, and the gantry needs to be properly tilted back. The load will not be raised other than when piling or filling. .
8. The elevation of the tons need to not obstruct the motorist's view. In special situations, when the product affects the forward vision, drive at a low rate when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it needs to be noted that the fork pointer ought to not touch various other goods or items. The lots should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the lots is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Overloading is banned, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for Stand-on Electric Pallet Stacker unique scenarios, such as the motorist does not leave the lorry's view and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look must be examined, and fuel, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the stress and temperature are normal.
5. After the forklift is running, the external leak must also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the car needs to be driven backwards when Stand-on Electric Pallet Stacker worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Solitary fork operation is not permitted.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not permitted to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844